Hello,

I've been reading the following notes:

Note 487972 - Tuning Livecache to the Linux OS

Note 767635 - MaxDB Version 7.5 parameter settings for OLTP/BW

Note 337445 - liveCache and memory management

Note 487972 - Operating system parameterization of liveCache

Note 941735 - SAP memory management for 64-bit Linux systems

There does not seem to be any Redhat specific tuning settings (though a couple of Suse recommendations), except for a general mention of all Linux systems with this direct I/O suggestion:

"As of Linux Version 2.6, we recommend that you set the parameter to the value YES rather than DEFAULT NO.

Further notes on this topic:

Note 977515:. Linux System paged during MaxDB data backup/add volume"

The parameters I am wanting to tune are in /etc/sysctl.conf, so since there does not seem to be any Livecache specific parameters, I was going to just take the general recommendations from Note 941735 - SAP memory management for 64-bit Linux systems and set our parameters as follows:

- kernel.shmall

As a configuration recommendation, kernel. shmall can be configured as the amount of virtual memory in the Linux system (RAM + Swap).

- kernel.shmmax

           This kernel parameter specifies how large an individual SysV Shared Memory Segment is allowed to be. In the case of an STD implementation, the parameter must be set sufficiently large in order to allow em/initial_size_MB. The value is specified in the unit Bytes so that "21474836480", for example, permits segments of 20 GB.

I am thinking to tune kernel.shmall to 90% of RAM+swap, and kernel.shmmax to 90% of RAM. Also will be setting the following parameters as well:

kernel.msgmni=1024

kernel.sem=1250 256000 100 1024

1. Parameter kernel.sem corresponds to "semmsl semmns semopm semmni"

vm.max_map_count=1000000

Does anyone out there have any different experiences or tips on how they set these up, specific to Livecache? The SAP application tuning is pretty straightforward, but wanted to make sure we didn't overlook anything with Livecache.

Thanks,

Derek

Hello,

We upgraded our livecache to 7.9 build 17. The scm side is upgraded 713 SP3. After we upgraded the livecache, when we start

livecache from LC10, livecache db starts up but when it starting dbnalyzer (dban_start ...), it crashes livecache and stop livecache. We can start

and stop livecache from dbmcli and livecache performs fine without dbanayzer. We also noticed after the upgrade, 7.9 does not like the maxcpu parameter =6. We had to lower that to 1 to start livecache as well.      

Steps for Reconstruction    

go to LC10 or dbanalyzer, try to start livecache or DB

analyzer:

WP_66 tracefile:

*** ERROR => EXECUTE C_0004 on connection 1, rc=-10807

bslsdb.cpp 9487]

SQLCODE : -10807

SQLERRTEXT : Connection down: [4] connection broken by kernel CRASH

sc_p=1160ce650,no=4,idc_p=

(nil),con=1,astyle='font-family:courier'

style='font-family:courier'

style='font-family:courier'

ct=1,slen=24,smax=256,#vars=0,stmt=1161936d0,table=dual

select 'Ping' from dual ;

***LOG BY2=> sql

error -10807 performing OPC [dbds 437]

***LOG BY0=> Connection down: [4] connection broken by kernel

CRASH [dbds 437]

Disconnecting from connection 1 ...

connection 1 is already down :

rc=-10821

SQLCODE : -10821

SQLERRTEXT : Session not connected

Now

I'm disconnected from MaxDB

start dbanlyzer using dbmcli:

mdt2ds11:li3adm> dbmcli -d LI3 -u control,control dban_start

ERR

-24994,ERR_RTE: Runtime environment error

4,connection broken server state 4

We have created an oss message as well and waiting a response from SAP..

Thanks

Dinali

Hi All,

We are installing SAP NW 7.4 with MaxDB 7.8 on Windows server 2008 R2, When in the phase Create database schema for ABAP  its giving error like below.

"[-4008] Unknown user name/password combination"

Below is the output from SdbCmdOut.log

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.models.software.Software | Software object initialized Sucessfully

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.models.database.DatabaseParameter | Create new database parameter object with name: MCOD value:  and comment:

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.JdbcDriver | JDBC driver path: D:\sapdb\programs\runtime\jar\sapdbc.jar

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.JdbcDriver | Class: com.sap.dbtech.powertoys.DBM loaded

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.JdbcDriver | Class: com.sap.dbtech.jdbc.DriverSapDB loaded

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.Xserver | Use Java process call.

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.Xserver | Execute command:  D:\sapdb\programs\bin\x_server.exe start

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.JdbcDriver | Establish dbmcli session

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.session.DbmJdbcSession | Connect to database: SID on host: HOSTNAME

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.session.DbmJdbcSession | Logon with user: control

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.session.DbmJdbcSession | Run command: param_directget MCOD

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.session.DbmJdbcSession | MCOD NO

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.session.DbmJdbcSession | Close dbmcli Session.

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.runtime.SdbLibInstance | End of command section: PARAM_GET

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.runtime.SdbLibInstance | *************************************************************

Tue Aug 12 20:31:20 IST 2014 | class com.sap.sdb.sllib.runtime.SdbLibInstance | Start new command section: GET_SQL_USERS

Tue Aug 12 20:31:20 IST 2014 | class com.sap.sdb.sllib.utils.Dbmcli | Use Java process call.

Tue Aug 12 20:31:20 IST 2014 | class com.sap.sdb.sllib.utils.Dbmcli | Execute command:  D:\sapdb\programs\pgm\dbmcli.exe -s dbm_version build

Tue Aug 12 20:31:20 IST 2014 | class com.sap.sdb.sllib.utils.sdbregview.SdbRegviewIsolated | Use Java process call.

Tue Aug 12 20:31:20 IST 2014 | class com.sap.sdb.sllib.utils.sdbregview.SdbRegviewIsolated | Execute command:  D:\sapdb\programs\bin\sdbregview.exe -l -delimiter -DELIM-

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.models.software.Software | Software object initialized Sucessfully

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.utils.connection.JdbcDriver | JDBC driver path: D:\sapdb\programs\runtime\jar\sapdbc.jar

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.utils.connection.JdbcDriver | Class: com.sap.dbtech.powertoys.DBM loaded

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.utils.connection.JdbcDriver | Class: com.sap.dbtech.jdbc.DriverSapDB loaded

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.utils.Xserver | Use Java process call.

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.utils.Xserver | Execute command:  D:\sapdb\programs\bin\x_server.exe start

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.utils.connection.session.SqlJdbcSession | Start new connection with URL: jdbc:sapdb://HOSTNAME/SID connect user: superdba

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.utils.DbCommand | com.sap.dbtech.jdbc.exceptions.DatabaseException: [-4008]: Unknown user name/password combination

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.api.exceptions.DatabaseCommandException | com.sap.sdb.sllib.utils.connection.JdbcDriver.createSqlSession(JdbcDriver.java:69)

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.api.exceptions.DatabaseCommandException | com.sap.sdb.sllib.utils.DbCommand.getAllSqlUsers(DbCommand.java:2054)

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.api.exceptions.DatabaseCommandException | com.sap.sdb.sllib.utils.cmd.ident.classes.GET_SQL_USERS.run(GET_SQL_USERS.java:26)

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.api.exceptions.DatabaseCommandException | com.sap.sdb.sllib.utils.DbCommand.runCommand(DbCommand.java:3469)

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.api.exceptions.DatabaseCommandException | com.sap.sdb.core.main.cmd.SdbCmdMain.<init>(SdbCmdMain.java:67)

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.api.exceptions.DatabaseCommandException | com.sap.sdb.core.main.cmd.SdbCmdMain.main(SdbCmdMain.java:212)

Kindly Suggest me to resolve.

Regards,

JD.S

I'm installing SAP Netweaver 7.3 Developer Workplace on MaxDB and I've got a look of GBs of files but I can't seem to find the MAXDB anywhere.

It says I need label MAXDB:78xxx:RDBMS:MAX DB:WINDOWS_X86_64:*.

Anyone can tell me the file name? (example 51042312_16).

I can find SQL Server and Oracle but no MaxDB.

Hi,

I am new to MAXDB and installed SAP system on Windows XP on local machine.

I have installed SAP Netweaver and while connecting to MAXDB via MAXDB Database Manager facing issue.

I am getting error as -2 ERR_USRFAIL:User authorization failed. Please check attached screenshot for more details.

I tried to connect via credentials provided in this thread http://scn.sap.com/thread/95219  but failed to do so.

I used following ports for connection:

           7200

           7210

           7269

           7270

           7575

Can anyone provide port, default username and password.?

Feedback appreciated.

Good day all

I have performed a restore of our production database (SIP) to our QA database (SIQ). The database starts up fine. When I attempt to start

SAP, I get a problem with a Unknown user name/password combination error in the dev_w0 trace.

C Fri Oct 03 14:44:18 2014

C  *** ERROR => Connect to database failed, rc = -4008 (POS(1) Unknown user name/password combination)

[dbsdbsql.cpp 139]

B  ***LOG BY2=> sql error -4008  performing CON [dbsh         1246]

B  ***LOG BY0=> POS(1) Unknown user name/password combination [dbsh         1246]

B  ***LOG BY2=> sql error -4008  performing CON [dblink       544]

B  ***LOG BY0=> POS(1) Unknown user name/password combination [dblink       544]

M  ***LOG R19=> ThInit, db_connect ( DB-Connect 000256) [thxxhead.c   1521]

M  in_ThErrHandle: 1

M  *** ERROR => ThInit: db_connect (step 1, th_errno 13, action 3, level 1) [thxxhead.c   11445]

M 

I have followed notes 39439 and 1871308 and still no luck. The xuser list command lists the four xuser entries that are expected for siqadm.

I cant find anything here or on Marketplace that resolves my problem, although there seems to be a lot of similar incidents reported.

Any help and guidance is appreciated.

Regards

Ray Phillips

I folks,

I use a 32 bits IDE witch connect to MaxDB using ODBC, so i need the 32 bit driver to create a 32 bits ODBC datasource.

Everything was OK, until ia receive a brand new computer, running... Windows 7 64 bits.

When i try to install MaxDb client (7.6.06.22), i have this message:

Cannot create package tree: unresolved dependency: package "Database connectivity" not found.

I've also tried version 7.8.02.21, and i get another message:

Software isn't runnable on your system.

What must i do ?

TIA

Frédéric.

Hi All,

We are installing SAP NW 7.4 with MaxDB 7.8 on Windows server 2008 R2, When in the phase Create database schema for ABAP  its giving error like below.

"[-4008] Unknown user name/password combination"

Below is the output from SdbCmdOut.log

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.models.software.Software | Software object initialized Sucessfully

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.models.database.DatabaseParameter | Create new database parameter object with name: MCOD value:  and comment:

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.JdbcDriver | JDBC driver path: D:\sapdb\programs\runtime\jar\sapdbc.jar

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.JdbcDriver | Class: com.sap.dbtech.powertoys.DBM loaded

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.JdbcDriver | Class: com.sap.dbtech.jdbc.DriverSapDB loaded

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.Xserver | Use Java process call.

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.Xserver | Execute command:  D:\sapdb\programs\bin\x_server.exe start

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.JdbcDriver | Establish dbmcli session

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.session.DbmJdbcSession | Connect to database: SID on host: HOSTNAME

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.session.DbmJdbcSession | Logon with user: control

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.session.DbmJdbcSession | Run command: param_directget MCOD

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.session.DbmJdbcSession | MCOD NO

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.utils.connection.session.DbmJdbcSession | Close dbmcli Session.

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.runtime.SdbLibInstance | End of command section: PARAM_GET

Tue Aug 12 20:31:19 IST 2014 | class com.sap.sdb.sllib.runtime.SdbLibInstance | *************************************************************

Tue Aug 12 20:31:20 IST 2014 | class com.sap.sdb.sllib.runtime.SdbLibInstance | Start new command section: GET_SQL_USERS

Tue Aug 12 20:31:20 IST 2014 | class com.sap.sdb.sllib.utils.Dbmcli | Use Java process call.

Tue Aug 12 20:31:20 IST 2014 | class com.sap.sdb.sllib.utils.Dbmcli | Execute command:  D:\sapdb\programs\pgm\dbmcli.exe -s dbm_version build

Tue Aug 12 20:31:20 IST 2014 | class com.sap.sdb.sllib.utils.sdbregview.SdbRegviewIsolated | Use Java process call.

Tue Aug 12 20:31:20 IST 2014 | class com.sap.sdb.sllib.utils.sdbregview.SdbRegviewIsolated | Execute command:  D:\sapdb\programs\bin\sdbregview.exe -l -delimiter -DELIM-

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.models.software.Software | Software object initialized Sucessfully

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.utils.connection.JdbcDriver | JDBC driver path: D:\sapdb\programs\runtime\jar\sapdbc.jar

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.utils.connection.JdbcDriver | Class: com.sap.dbtech.powertoys.DBM loaded

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.utils.connection.JdbcDriver | Class: com.sap.dbtech.jdbc.DriverSapDB loaded

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.utils.Xserver | Use Java process call.

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.utils.Xserver | Execute command:  D:\sapdb\programs\bin\x_server.exe start

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.utils.connection.session.SqlJdbcSession | Start new connection with URL: jdbc:sapdb://HOSTNAME/SID connect user: superdba

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.utils.DbCommand | com.sap.dbtech.jdbc.exceptions.DatabaseException: [-4008]: Unknown user name/password combination

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.api.exceptions.DatabaseCommandException | com.sap.sdb.sllib.utils.connection.JdbcDriver.createSqlSession(JdbcDriver.java:69)

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.api.exceptions.DatabaseCommandException | com.sap.sdb.sllib.utils.DbCommand.getAllSqlUsers(DbCommand.java:2054)

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.api.exceptions.DatabaseCommandException | com.sap.sdb.sllib.utils.cmd.ident.classes.GET_SQL_USERS.run(GET_SQL_USERS.java:26)

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.api.exceptions.DatabaseCommandException | com.sap.sdb.sllib.utils.DbCommand.runCommand(DbCommand.java:3469)

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.api.exceptions.DatabaseCommandException | com.sap.sdb.core.main.cmd.SdbCmdMain.<init>(SdbCmdMain.java:67)

Tue Aug 12 20:31:22 IST 2014 | class com.sap.sdb.sllib.api.exceptions.DatabaseCommandException | com.sap.sdb.core.main.cmd.SdbCmdMain.main(SdbCmdMain.java:212)

Kindly Suggest me to resolve.

Regards,

JD.S

Hi,

I have installed SAP Netweaver developer Studio 6.40 which installed MAXDB database also. Due to some reason I had to unistall the trial version of Developer studio, in this process developer studio got unistalled but not MAXDB.

*----

I use Add/Remove programs and uninstall MaxDB. I get the messages like this.....

Start uninstallation now (y/n) : Y (resoponse)

then message displays

found instance of J2E, cannot remove package..first remove all instances...

*----

I have stopped all the services, even then Iam getting such error message. How do I uninstall?

Help needed.

-Suresh

Hello,

I've been reading the following notes:

Note 487972 - Tuning Livecache to the Linux OS

Note 767635 - MaxDB Version 7.5 parameter settings for OLTP/BW

Note 337445 - liveCache and memory management

Note 487972 - Operating system parameterization of liveCache

Note 941735 - SAP memory management for 64-bit Linux systems

There does not seem to be any Redhat specific tuning settings (though a couple of Suse recommendations), except for a general mention of all Linux systems with this direct I/O suggestion:

"As of Linux Version 2.6, we recommend that you set the parameter to the value YES rather than DEFAULT NO.

Further notes on this topic:

Note 977515:. Linux System paged during MaxDB data backup/add volume"

The parameters I am wanting to tune are in /etc/sysctl.conf, so since there does not seem to be any Livecache specific parameters, I was going to just take the general recommendations from Note 941735 - SAP memory management for 64-bit Linux systems and set our parameters as follows:

- kernel.shmall

As a configuration recommendation, kernel. shmall can be configured as the amount of virtual memory in the Linux system (RAM + Swap).

- kernel.shmmax

           This kernel parameter specifies how large an individual SysV Shared Memory Segment is allowed to be. In the case of an STD implementation, the parameter must be set sufficiently large in order to allow em/initial_size_MB. The value is specified in the unit Bytes so that "21474836480", for example, permits segments of 20 GB.

I am thinking to tune kernel.shmall to 90% of RAM+swap, and kernel.shmmax to 90% of RAM. Also will be setting the following parameters as well:

kernel.msgmni=1024

kernel.sem=1250 256000 100 1024

1. Parameter kernel.sem corresponds to "semmsl semmns semopm semmni"

vm.max_map_count=1000000

Does anyone out there have any different experiences or tips on how they set these up, specific to Livecache? The SAP application tuning is pretty straightforward, but wanted to make sure we didn't overlook anything with Livecache.

Thanks,

Derek

Hi,

on MAX DB 7.8 on Win 2008 some queries fail with

isolated index scans

error message.

Any idea about that.

Thank you.

Hello,

i have installed a new ERP 6.06 SAP System on MaxDB 7.9/Sles 11 Linux. After successful installation i have tested the database connection.

The database connection failed. What could i do to solve the problem?

SAP transaction DB59 Test:

Result:

p01_P01_02 (p01 )

SAP Kernel Release : 720_EXT_REL

SAP Kernel Patch : 401

DBMRFC Release : 7.9.07.14

DBMCLI Release : 7.9.07.14

DBSL Release : 720.00

DBSL Patch : 421

SQLDBC Version : 7.8.02.17

SQLDBC Runtime : 7.9.07.14

1.DBSL Library Availability -Connection test successful

2.Client Software Availability -Connection test successful

3.Execute an external operating system command (DBMCLI) -Connection test successful

4.Determine status using SQL connection -Error in connection test

5.Test the SQL connection (Native SQL at CON_NAME) -Connection test successful

Report: RSSDBCHECKDBMRFC

  Main Analysis

       SMGW - Checking existence and correctness of registered client

       WARNING: dbmrfc@sapdb not registered. Trying to start the SAPDB_DBM_DAEMON

       SM59 - Checking existence and connection of RFC destinations SAPDB_DBM and SAPDB_DBM_DAEMON

       SAPDB_DBM exists

       SAPDB_DBM_DAEMON exists

       SAPDB_DBM connection successful

       WARNING: SAPDB_DBM_DAEMON connection not successful. Trying to start SAPDB_DBM_DAEMON

       SM59 - Checks were successful

       CONN - Determining database state via TCP/IP connection SAPDB_DBM and SAPDB_DBM_DAEMON

  DBM_EXECUTE_SDB error: dbm_execute_error

  Name and Server     : P01 - p01

  Function            : DBM_EXECUTE

  Command             : db_state

  Error               : DBM Error

  Return Code         : -24941

  Error Message       : ERR_NEEDLOGON: DBM server logon required

  ERR

  -24941,ERR_NEEDLOGON: DBM server logon required

       ERROR: Error in determination via command mode "dbmrfc db_state"

  DBM_EXECUTE_SDB: dbm_execute_error

  Name and Server     : P01 - p01

  Function            : DBM_EXECUTE

  Command             : db_state

  Error               : DBM Error

  Return Code         : -24941

  Error Message       : ERR_NEEDLOGON: DBM server logon required

  ERR

  -24941,ERR_NEEDLOGON: DBM server logon required

       ERROR: Error in determination via session mode "dbmrfc db_state"

       CONN - Check was not successful

       TP - Get connection information and existence of program

       Connection information used by DBMRFC:

       dbnode: p01 ; dbname: P01 ; sysid: P01 ; conn: P01 ; profile: no_longer_used

       Transport profile is not specified, trying to determine it

       ERROR in TMS_CFG_READ_LOCAL_CONFIG:  tms_is_not_configured

       ERROR in TMS_CFG_READ_LOCAL_CONFIG: Could not get transport domain.

       Executing command: dbmcli -d P01 -n p01 -tpp no_longer_used -tpi P01 -tpc P01 db_state

       TP - Checks were successful

Detail Analysis

       Checking MAXDB Version and searching independent program path via SDBREGVIEW

       Independent program path exists: /sapdb/programs

       Client installation path exists: /sapdb/clients/P01

       Checking paths in environment variables

       Checking correctness of environment variable "path"

       /sapdb/programs/bin  exists

       ERROR: Set the following path before all other paths in environment variable: /sapdb/clients/P01/bin

       /usr/sap/P01/DVEBMGS02/exe (DIR_EXECUTABLE) exists

       Checking correctness of environment variable "ld_library_path"

       /usr/sap/P01/DVEBMGS02/exe (DIR_EXECUTABLE) exists

       ERROR: Set the following path before all other paths in environment variable: /sapdb/programs/lib

       ERROR: Set the following path before all other paths in environment variable: /sapdb/clients/P01/lib

       Error found in one step

       Checking existence of necessary libraries in /sapdb/programs/lib

       libicudata.so.<version> exists

       libicui18n.so.<version> exists

       libicuuc.so.<version> exists

       libsapni.so exists

       WARNING: libsapu16.so was not found

       Check your MAXDB installation

       Checking existence of necessary executables

       tp exists in /usr/sap/P01/DVEBMGS02/exe

       sapdbmrfc exists in /usr/sap/P01/DVEBMGS02/exe

       dbmrfc exists in /sapdb/programs/bin

       sdbregview exists in /sapdb/programs/bin

       sdbverify exists in /sapdb/programs/bin

       dbmcli exists in /sapdb/programs/bin

Xuser test on OS:

p01:p01adm 57> dbmcli -U c

dbmcli on p01 : P01>exit

OK

---

p01:p01adm 58> dbmcli -U w

dbmcli on p01 : P01>exit

OK

---

p01:p01adm 59> dbmcli -d P01 -u control,<password>

dbmcli on P01>exit

OK

---

p01:p01adm 59> dbmcli -d P01 -u superdba,<password>

dbmcli on P01>exit

OK

---

p01:p01adm 61> R3trans -d

This is R3trans version 6.23 (release 720 - 31.10.12 - 20:12:06).

unicode enabled version

R3trans finished (0000).

p01:p01adm 62> R3trans -x

This is R3trans version 6.23 (release 720 - 31.10.12 - 20:12:06).

unicode enabled version

R3trans finished (0000).

p01:p01adm 63>

p01:p01adm 58> dbmcli -d P01 -U c db_enum

OK

P01     /sapdb/P01/db                           7.9.07.14       fast    running

P01     /sapdb/P01/db                           7.9.07.14       quick   offline

P01     /sapdb/P01/db                           7.9.07.14       slow    offline

P01     /sapdb/P01/db                           7.9.07.14       test    offline

p01:p01adm 59>

p01:p01adm 60> x_server start

2013-10-19 12:17:28 30139 44640 INF  12916          Found running XServer on port 7200

2013-10-19 12:17:28 30139 44640 INF  13011            version 'U64/LIX86 7.9.07   Build 014-123-244-287'

2013-10-19 12:17:28 30139 44640 INF  13010            installation P01  - path: /sapdb/P01/db

2013-10-19 12:17:28 30141 86336 ERR  11931 XSERVER  Open update pipe '/sapdb/data/fifo/xserver_p01_update' failed:No such file or directory

2013-10-19 12:17:28 30141 86336 INF  12916          Found running sdbgloballistener on port 7210

2013-10-19 12:17:28 30141 86336 INF  13011            version 'UNKNOWN'

2013-10-19 12:17:28 30141 86336 ERR  11941 XSERVER  Version string conversion failed:expected format %-9.9s %-8.8s Build %-3.3s-%-11.11s

p01:p01adm 60>

p01:p01adm 60> cd /sapdb/data/fifo/

p01:p01adm 61> ls -altr

total 8

drwxrwxr-x 12 sdb sdba 4096 Oct 18 18:30 ..

prw-rw----  1 sdb sdba    0 Oct 19 12:05 xserver_p01_7200_logger

prw--w--w-  1 sdb sdba    0 Oct 19 12:05 P01

prw-rw----  1 sdb sdba    0 Oct 19 12:17 xserver_p01_7200_update

drwxrwxr-x  2 sdb sdba 4096 Oct 19 12:17 .

p01:p01adm 62>

There´s no entry with "xserver_p01_update"

How can i create this entry?

I have no idea to solved this problem. Who can help?

Best regards

Dennis

Hi community,

right now I am facing an issue with the standard monitoring, which is provided by SAP (SAP BASIS 701) for MaxDB (7.7). Im am using the following MTE:

TCode "RZ20" --> SAP CCMS Monitor Templates --> Database --> MaxDB --> Properties --> State --> Current State

I have changed nothing and I am using this MTE as it is. From time to time the Node tells me "Could not determine the current status" and changes status to "Yellow" although the DB is online. As well if I "activate maintenance function" within this transaction and start the analysis method for the MTE "Current state" manualy, it shows me, that the DB is doing fine. The node's state nevertheless remains yellow with "Could not determine current status".

After some time and for no obvious reason the Node's state switches back to green again.

Has anybody come across this issue or has an idea where to start further investigation?

Thanks in advance and regards,

Jochen

Hi All ,

I am trying to install SAP  trial version . While installation of MAXDB serve , I am getting an error " Some database application might still be running"

I dont have any other database installed on my system .

Kindly reply what can be the possible reason for this .

Thanks n Regards

Manik L Dhakate

HI All

I need to set automatic backup in MaxDB, i have seen automatic option for logs but not for Full database, Can anyone explain how we can do this.

I want Full backup on daily basis along with logs.

Welcome for suggestion and directions.

Regards,

YR

Hello,

I've been reading the following notes:

Note 487972 - Tuning Livecache to the Linux OS

Note 767635 - MaxDB Version 7.5 parameter settings for OLTP/BW

Note 337445 - liveCache and memory management

Note 487972 - Operating system parameterization of liveCache

Note 941735 - SAP memory management for 64-bit Linux systems

There does not seem to be any Redhat specific tuning settings (though a couple of Suse recommendations), except for a general mention of all Linux systems with this direct I/O suggestion:

"As of Linux Version 2.6, we recommend that you set the parameter to the value YES rather than DEFAULT NO.

Further notes on this topic:

Note 977515:. Linux System paged during MaxDB data backup/add volume"

The parameters I am wanting to tune are in /etc/sysctl.conf, so since there does not seem to be any Livecache specific parameters, I was going to just take the general recommendations from Note 941735 - SAP memory management for 64-bit Linux systems and set our parameters as follows:

- kernel.shmall

As a configuration recommendation, kernel. shmall can be configured as the amount of virtual memory in the Linux system (RAM + Swap).

- kernel.shmmax

           This kernel parameter specifies how large an individual SysV Shared Memory Segment is allowed to be. In the case of an STD implementation, the parameter must be set sufficiently large in order to allow em/initial_size_MB. The value is specified in the unit Bytes so that "21474836480", for example, permits segments of 20 GB.

I am thinking to tune kernel.shmall to 90% of RAM+swap, and kernel.shmmax to 90% of RAM. Also will be setting the following parameters as well:

kernel.msgmni=1024

kernel.sem=1250 256000 100 1024

1. Parameter kernel.sem corresponds to "semmsl semmns semopm semmni"

vm.max_map_count=1000000

Does anyone out there have any different experiences or tips on how they set these up, specific to Livecache? The SAP application tuning is pretty straightforward, but wanted to make sure we didn't overlook anything with Livecache.

Thanks,

Derek

Hi,

          I am using MaxDB 7.6 Version .Currently trying out Syncronization Manager To Replicate MAXDB Database To Mysql Database (Server(maxdb db name: MASTERDB) To Client(mysql db name : CLIENTDB ) ).I have MAXDB And MYSQL in Same Machine.Also copied sapdbc.jar,com.mysql.driver.jar in /lib  folder.

I have configured and started Message server & Syncservice  for maxdb database MASTERDB Only.Currently,Iam stucked out in Syncmangui while configuring mysql as client . I could chose mysql driver but i couldnt connect to mysql.Also I want to know whether  to configure Message server and Syncserver for MysqlDB and also i want to know whether iam missing steps in client side.If iam missing steps please suggest me.

Steps I Followed

-------------------------

1.Running Maxdb Database : (db_online)

2.msgserver start ( maxdb  database instance)

3. syncservice (maxdb database instance).

4.syncmangui

          added replication table for maxdb MASTERDATABASE

          for client i tried mysql db name but i couldnt connect to it.I have selected mysql driver jar

Thanks

Hi All

I want to perform OS/DB migration from MS-SQL (windows ) to sap MaxDB windows.

I have to prepare estimation for db migration from MSSql to SAP MaxDB

please forward me If you have any  estimation & migration work instruction, planning  and Documentation for reference documents.

may mail id : deerusap@gmail.com

Regards

Diru

Hi gurues, I'm facing this issue with an IDES on MaxDB with Windows.

System was up and running until someone tries to make an upgrade of the kernel. Since then we can not start our system. we tried to rollback kernel release to the previous one but it didn't work.

When we start our system from MMC console we can see all process in green but work processes are in RUN state and after a few minutes they goes down with the following error

-

trc file: "dev_w0", trc level: 1, release: "701"

-

*

• ACTIVE TRACE LEVEL           1

• ACTIVE TRACE COMPONENTS      all, MJ

*

B 

B Mon May 16 23:57:31 2011

B  create_con (con_name=R/3)

B  Loading DB library '
sirillium1\sapmnt\SED\SYS\exe\uc\NTAMD64\dbsdbslib.dll' ...

B  Library '
sirillium1\sapmnt\SED\SYS\exe\uc\NTAMD64\dbsdbslib.dll' loaded

B  Version of '
sirillium1\sapmnt\SED\SYS\exe\uc\NTAMD64\dbsdbslib.dll' is "700.08", patchlevel (0.24)

B  New connection 0 created

M sysno      00

M sid        SED

M systemid   562 (PC with Windows NT)

M relno      7010

M patchlevel 0

M patchno    32

M intno      20020600

M make:      multithreaded, Unicode, 64 bit, optimized

M pid        212

M

M  kernel runs with dp version 241000(ext=110000) (@(#) DPLIB-INT-VERSION-241000-UC)

M  length of sys_adm_ext is 576 bytes

M  ***LOG Q0Q=> tskh_init, WPStart (Workproc 0 212) [dpxxdisp.c   1348]

I  MtxInit: 30000 0 0

M  DpSysAdmExtCreate: ABAP is active

M  DpSysAdmExtCreate: VMC (JAVA VM in WP) is not active

M  DpShMCreate: sizeof(wp_adm)          22784     (1752)

M  DpShMCreate: sizeof(tm_adm)          5912704     (29416)

M  DpShMCreate: sizeof(wp_ca_adm)          24064     (80)

M  DpShMCreate: sizeof(appc_ca_adm)     8000     (80)

M  DpCommTableSize: max/headSize/ftSize/tableSize=500/16/552064/552080

M  DpShMCreate: sizeof(comm_adm)          552080     (1088)

M  DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=0/0/0/0/0

M  DpShMCreate: sizeof(slock_adm)          0     (104)

M  DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0

M  DpShMCreate: sizeof(file_adm)          0     (72)

M  DpShMCreate: sizeof(vmc_adm)          0     (1864)

M  DpShMCreate: sizeof(wall_adm)          (41664/36752/64/192)

M  DpShMCreate: sizeof(gw_adm)     48

M  DpShMCreate: SHM_DP_ADM_KEY          (addr: 000000000B2C0050, size: 6607136)

M  DpShMCreate: allocated sys_adm at 000000000B2C0050

M  DpShMCreate: allocated wp_adm at 000000000B2C2270

M  DpShMCreate: allocated tm_adm_list at 000000000B2C7B70

M  DpShMCreate: allocated tm_adm at 000000000B2C7BD0

M  DpShMCreate: allocated wp_ca_adm at 000000000B86B450

M  DpShMCreate: allocated appc_ca_adm at 000000000B871250

M  DpShMCreate: allocated comm_adm at 000000000B873190

M  DpShMCreate: system runs without slock table

M  DpShMCreate: system runs without file table

M  DpShMCreate: allocated vmc_adm_list at 000000000B8F9E20

M  DpShMCreate: allocated gw_adm at 000000000B8F9EA0

M  DpShMCreate: system runs without vmc_adm

M  DpShMCreate: allocated ca_info at 000000000B8F9ED0

M  DpShMCreate: allocated wall_adm at 000000000B8F9EE0

M 

M Mon May 16 23:57:32 2011

M  rdisp/queue_size_check_value :  -> off

M  ThTaskStatus: rdisp/reset_online_during_debug 0

X  EmInit: MmSetImplementation( 2 ).

X  MM global diagnostic options set: 0

X  <ES> client 0 initializing ....

X  Using implementation view

X  <EsNT> Using memory model view.

M  <EsNT> Memory Reset disabled as NT default

X  ES initialized.

M  ThInit: running on host sirillium1

M 

M Mon May 16 23:57:33 2011

M  calling db_connect ...

C 

C  DBSDBSLIB : version 700.08, patch 0.024 (Make PL 0.32)

C  MAXDB shared library (dbsdbslib) patchlevels (last 10)

C    (0.024) Default value for max. input variables is 2000 (note 655018)

C    (0.024) Profile parameter to define max. input variables (note 655018)

C    (0.024) Switch SQLMODE after CREATE INDEX SERIAL (note 1267841)

C    (0.024) Input parameters for SQL statements increased (note 655018)

C    (0.018) Create index serial for MaxDB 7.6 (note 1267841)

C    (0.018) More trace in case of packed to string conversion error (note 1262799)

C    (0.016) R3trans export aborts with signal 6 (note 1262245)

C    (0.009) IA64 alignment errors (note 1245982)

C    (0.007) Support DB-Type 'SAP DB' by UPDSTAT (note 1225668)

C 

C 

C  Loading SQLDBC client runtime ...

C  SQLDBC SDK Version : SQLDBC.H  7.6.0    BUILD 007-123-091-175

C  SQLDBC Library Version : libSQLDBC 7.6.5    BUILD 015-123-202-938

C  SQLDBC client runtime is MaxDB 7.6.5.015 CL 202938

C  SQLDBC supports new DECIMAL interface : 0

C  SQLDBC supports VARIABLE INPUT data   : 1

C  SQLDBC supports keepAlive indicator   : 0

C  INFO : SQLOPT= -I 0 -t 0 -S SAPR3

C  Try to connect (DEFAULT) on connection 0 ...

C  *** ERROR => Connect to database failed, rc = -10709 (Connection failed (RTE:Database name is missing))

[dbsdbsql.cpp 137]

B  ***LOG BV3=> severe db error -10709    ; work process is stopped [dbsh#2 @ 1203] [dbsh    1203 ]

B  ***LOG BY2=> sql error -10709 performing CON [dblink#3 @ 431] [dblink  0431 ]

B  ***LOG BY0=> Connection failed (RTE:Database name is missing) [dblink#3 @ 431] [dblink  0431 ]

M  ***LOG R19=> ThInit, db_connect ( DB-Connect 000256) [thxxhead.c   1449]

M  in_ThErrHandle: 1

M  *** ERROR => ThInit: db_connect (step 1, th_errno 13, action 3, level 1) [thxxhead.c   10563]

M 

M  Info for wp 0

M 

M    pid = 212

M    severity = 0

M    status = 0

M    stat = WP_RUN

M    waiting_for = NO_WAITING

M    reqtype = DP_RQ_DIAWP

M    act_reqtype = NO_REQTYPE

M    rq_info = 0

M    tid = -1

M    mode = 255

M    len = -1

M    rq_id = 65535

M    rq_source =

M    last_tid = 0

M    last_mode = 0

M    semaphore = 0

M    act_cs_count = 0

M    csTrack = 0

M    csTrackRwExcl = 0

M    csTrackRwShrd = 0

M    mode_cleaned_counter = 0

M    control_flag = 0

M    int_checked_resource(RFC) = 0

M    ext_checked_resource(RFC) = 0

M    int_checked_resource(HTTP) = 0

M    ext_checked_resource(HTTP) = 0

M    report = >                                        <

M    action = 0

M    tab_name = >                              <

M    attachedVm = no VM

M 

M  *****************************************************************************

M  *

M  *  LOCATION    SAP-Server sirillium1_SED_00 on host sirillium1 (wp 0)

M  *  ERROR       ThInit: db_connect

M  *

M  *  TIME        Mon May 16 23:57:33 2011

M  *  RELEASE     701

M  *  COMPONENT   Taskhandler

M  *  VERSION     1

M  *  RC          13

M  *  MODULE      thxxhead.c

M  *  LINE        10783

M  *  COUNTER     1

M  *

M  *****************************************************************************

M 

M  PfStatDisconnect: disconnect statistics

M  Entering TH_CALLHOOKS

M  ThCallHooks: call hook >BtcCallLgCl< for event BEFORE_DUMP

M  ThCallHooks: call hook >ThrSaveSPAFields< for event BEFORE_DUMP

M  *** ERROR => ThrSaveSPAFields: no valid thr_wpadm [thxxrun1.c   723]

M  *** ERROR => ThCallHooks: event handler ThrSaveSPAFields for event BEFORE_DUMP failed [thxxtool3.c  261]

M  Entering ThSetStatError

M  ThIErrHandle: do not call ThrCoreInfo (no_core_info=0, in_dynp_env=0)

M  Entering ThReadDetachMode

M  call ThrShutDown (1)...

M  ***LOG Q02=> wp_halt, WPStop (Workproc 0 212) [dpnttool.c   334]

We check several entries on this SDN site, and look for a lot of notes on the marketplace, and they always are related to default user in xuser files, but our xuser list output is ok. We have a DEFAULT connection to SAPSID user, a DBM connection to CONTROL user and a USERDBA connection.

-

XUSER Entry  1

-

Key         :DEFAULT          

Username    :SAPSID                                                         

UsernameUCS2:S.A.P.S.E.D. . . . . . . . . . . . . . . . . . . . . . . . . . .

Password    :?????????

PasswordUCS2:?????????

Dbname      :SID              

Nodename    :server1                                                     

Sqlmode     :SAPR3  

Cachelimit  :-1

Timeout    

Isolation  

Charset     :<unspecified>    

-

XUSER Entry  2

-

Key         :c                

Username    :CONTROL                                                        

UsernameUCS2:C.O.N.T.R.O.L. . . . . . . . . . . . . . . . . . . . . . . . . .

Password    :?????????

PasswordUCS2:?????????

Dbname      :SID              

Nodename    :server1                                                     

Sqlmode     :INTERNAL

Cachelimit  :-1

Timeout     :-1

Isolation   :-1

Charset     :<unspecified>    

-

XUSER Entry  3

-

Key         :c_J2EE           

Username    :CONTROL                                                        

UsernameUCS2:C.O.N.T.R.O.L. . . . . . . . . . . . . . . . . . . . . . . . . .

Password    :?????????

PasswordUCS2:?????????

Dbname      :SID              

Nodename    :server1                                                     

Sqlmode     :SAPR3  

Cachelimit  :-1

Timeout    

Isolation  

Charset     :<unspecified>    

-

XUSER Entry  4

-

Key         :w                

Username    :SUPERDBA                                                       

UsernameUCS2:S.U.P.E.R.D.B.A. . . . . . . . . . . . . . . . . . . . . . . . .

Password    :?????????

PasswordUCS2:?????????

Dbname      :SID              

Nodename    :server1                                                     

Sqlmode     :INTERNAL

Cachelimit  :-1

Timeout     :-1

Isolation   :-1

Charset     :<unspecified>    

Any idea? we are out of ideas at this moment.

Regards

Edited by: Gustavo Goicochea on May 17, 2011 6:37 PM

Hello,

i have installed a new ERP 6.06 SAP System on MaxDB 7.9/Sles 11 Linux. After successful installation i have tested the database connection.

The database connection failed. What could i do to solve the problem?

SAP transaction DB59 Test:

Result:

p01_P01_02 (p01 )

SAP Kernel Release : 720_EXT_REL

SAP Kernel Patch : 401

DBMRFC Release : 7.9.07.14

DBMCLI Release : 7.9.07.14

DBSL Release : 720.00

DBSL Patch : 421

SQLDBC Version : 7.8.02.17

SQLDBC Runtime : 7.9.07.14

1.DBSL Library Availability -Connection test successful

2.Client Software Availability -Connection test successful

3.Execute an external operating system command (DBMCLI) -Connection test successful

4.Determine status using SQL connection -Error in connection test

5.Test the SQL connection (Native SQL at CON_NAME) -Connection test successful

Report: RSSDBCHECKDBMRFC

  Main Analysis

       SMGW - Checking existence and correctness of registered client

       WARNING: dbmrfc@sapdb not registered. Trying to start the SAPDB_DBM_DAEMON

       SM59 - Checking existence and connection of RFC destinations SAPDB_DBM and SAPDB_DBM_DAEMON

       SAPDB_DBM exists

       SAPDB_DBM_DAEMON exists

       SAPDB_DBM connection successful

       WARNING: SAPDB_DBM_DAEMON connection not successful. Trying to start SAPDB_DBM_DAEMON

       SM59 - Checks were successful

       CONN - Determining database state via TCP/IP connection SAPDB_DBM and SAPDB_DBM_DAEMON

  DBM_EXECUTE_SDB error: dbm_execute_error

  Name and Server     : P01 - p01

  Function            : DBM_EXECUTE

  Command             : db_state

  Error               : DBM Error

  Return Code         : -24941

  Error Message       : ERR_NEEDLOGON: DBM server logon required

  ERR

  -24941,ERR_NEEDLOGON: DBM server logon required

       ERROR: Error in determination via command mode "dbmrfc db_state"

  DBM_EXECUTE_SDB: dbm_execute_error

  Name and Server     : P01 - p01

  Function            : DBM_EXECUTE

  Command             : db_state

  Error               : DBM Error

  Return Code         : -24941

  Error Message       : ERR_NEEDLOGON: DBM server logon required

  ERR

  -24941,ERR_NEEDLOGON: DBM server logon required

       ERROR: Error in determination via session mode "dbmrfc db_state"

       CONN - Check was not successful

       TP - Get connection information and existence of program

       Connection information used by DBMRFC:

       dbnode: p01 ; dbname: P01 ; sysid: P01 ; conn: P01 ; profile: no_longer_used

       Transport profile is not specified, trying to determine it

       ERROR in TMS_CFG_READ_LOCAL_CONFIG:  tms_is_not_configured

       ERROR in TMS_CFG_READ_LOCAL_CONFIG: Could not get transport domain.

       Executing command: dbmcli -d P01 -n p01 -tpp no_longer_used -tpi P01 -tpc P01 db_state

       TP - Checks were successful

Detail Analysis

       Checking MAXDB Version and searching independent program path via SDBREGVIEW

       Independent program path exists: /sapdb/programs

       Client installation path exists: /sapdb/clients/P01

       Checking paths in environment variables

       Checking correctness of environment variable "path"

       /sapdb/programs/bin  exists

       ERROR: Set the following path before all other paths in environment variable: /sapdb/clients/P01/bin

       /usr/sap/P01/DVEBMGS02/exe (DIR_EXECUTABLE) exists

       Checking correctness of environment variable "ld_library_path"

       /usr/sap/P01/DVEBMGS02/exe (DIR_EXECUTABLE) exists

       ERROR: Set the following path before all other paths in environment variable: /sapdb/programs/lib

       ERROR: Set the following path before all other paths in environment variable: /sapdb/clients/P01/lib

       Error found in one step

       Checking existence of necessary libraries in /sapdb/programs/lib

       libicudata.so.<version> exists

       libicui18n.so.<version> exists

       libicuuc.so.<version> exists

       libsapni.so exists

       WARNING: libsapu16.so was not found

       Check your MAXDB installation

       Checking existence of necessary executables

       tp exists in /usr/sap/P01/DVEBMGS02/exe

       sapdbmrfc exists in /usr/sap/P01/DVEBMGS02/exe

       dbmrfc exists in /sapdb/programs/bin

       sdbregview exists in /sapdb/programs/bin

       sdbverify exists in /sapdb/programs/bin

       dbmcli exists in /sapdb/programs/bin

Xuser test on OS:

p01:p01adm 57> dbmcli -U c

dbmcli on p01 : P01>exit

OK

---

p01:p01adm 58> dbmcli -U w

dbmcli on p01 : P01>exit

OK

---

p01:p01adm 59> dbmcli -d P01 -u control,<password>

dbmcli on P01>exit

OK

---

p01:p01adm 59> dbmcli -d P01 -u superdba,<password>

dbmcli on P01>exit

OK

---

p01:p01adm 61> R3trans -d

This is R3trans version 6.23 (release 720 - 31.10.12 - 20:12:06).

unicode enabled version

R3trans finished (0000).

p01:p01adm 62> R3trans -x

This is R3trans version 6.23 (release 720 - 31.10.12 - 20:12:06).

unicode enabled version

R3trans finished (0000).

p01:p01adm 63>

p01:p01adm 58> dbmcli -d P01 -U c db_enum

OK

P01     /sapdb/P01/db                           7.9.07.14       fast    running

P01     /sapdb/P01/db                           7.9.07.14       quick   offline

P01     /sapdb/P01/db                           7.9.07.14       slow    offline

P01     /sapdb/P01/db                           7.9.07.14       test    offline

p01:p01adm 59>

p01:p01adm 60> x_server start

2013-10-19 12:17:28 30139 44640 INF  12916          Found running XServer on port 7200

2013-10-19 12:17:28 30139 44640 INF  13011            version 'U64/LIX86 7.9.07   Build 014-123-244-287'

2013-10-19 12:17:28 30139 44640 INF  13010            installation P01  - path: /sapdb/P01/db

2013-10-19 12:17:28 30141 86336 ERR  11931 XSERVER  Open update pipe '/sapdb/data/fifo/xserver_p01_update' failed:No such file or directory

2013-10-19 12:17:28 30141 86336 INF  12916          Found running sdbgloballistener on port 7210

2013-10-19 12:17:28 30141 86336 INF  13011            version 'UNKNOWN'

2013-10-19 12:17:28 30141 86336 ERR  11941 XSERVER  Version string conversion failed:expected format %-9.9s %-8.8s Build %-3.3s-%-11.11s

p01:p01adm 60>

p01:p01adm 60> cd /sapdb/data/fifo/

p01:p01adm 61> ls -altr

total 8

drwxrwxr-x 12 sdb sdba 4096 Oct 18 18:30 ..

prw-rw----  1 sdb sdba    0 Oct 19 12:05 xserver_p01_7200_logger

prw--w--w-  1 sdb sdba    0 Oct 19 12:05 P01

prw-rw----  1 sdb sdba    0 Oct 19 12:17 xserver_p01_7200_update

drwxrwxr-x  2 sdb sdba 4096 Oct 19 12:17 .

p01:p01adm 62>

There´s no entry with "xserver_p01_update"

How can i create this entry?

I have no idea to solved this problem. Who can help?

Best regards

Dennis